IC HT12D PDF

0 Comments

HT12D is a series decoder IC for remote control applications manufactured by Holtek. It is commonly used for radio frequency (RF) applications. Download. RF transmitter and RF receiver of Mhz; 3 push buttons; IC HT12D; IC HT12E; Hearders (male or female it doesn’t care); 3 resistors with a value from ( to. HT12D is a decoder integrated circuit that belongs to series of decoders. This series of decoders are mainly used for remote control system applications, like.

Author: Vogar Tacage
Country: Canada
Language: English (Spanish)
Genre: Health and Food
Published (Last): 25 February 2010
Pages: 210
PDF File Size: 13.47 Mb
ePub File Size: 3.33 Mb
ISBN: 760-4-84729-518-2
Downloads: 47182
Price: Free* [*Free Regsitration Required]
Uploader: Nikonos

To know how a 4-bit data can be encoded and then send to the input pin of this IC, we have to understand the working of the HT12E Encoder IC which is given here. Can be used in Home automation for short range remote switching Safety systems like Burglar alarm system, Smoke or Fire alarm system etc.

The 4-bit data that is received can be obtained on pins AD0 to AD1 and an address of 8-bit has to be set using the pins A0 to A7.

TL — Programmable Reference Voltage. This high-density System-in-Package SiP integrates controller, power switches, and support components.

How IC HT12D works? | JAY Robotics’s Blog

A valid transmission in indicated by a high signal at VT pin. Connected to the Ground of circuit. Interface GPS with Arduino.

If you want security you can connect any of the 8 pins to 5V to make it high. It is not mandatory to use it. Skip to main content. In the above circuit I have set the 8-bit address data as 0b, by connecting all address pins to ground.

  HCPL 4562 PDF

HT12D Decoder IC

It is very important that your Decoder should have the same address of that of the encoder. Submitted by admin on 27 October These are the 8-bit address bits, which is used to protect your data.

This series of decoders are mainly used ix remote control system applications, like burglar alarm, car door controller, security system etc. The data on 4 bit latch type output pins remain unchanged until new is received. It decodes the serial addresses and data received by, say, an RF receiver, into parallel data and sends them to output data pins.

What is Web Browser.

HT12D Decoder IC | HT12D Datasheet | Pin Diagram

They can also be connected to LED to physically view the received data. SPI Module of Arduino. The IC is should be powered by 5V pin 18 and the ground pin pin 9 is grounded. Virgin Galactic — Commercial Space Flight. These two ICs together form an Encoder and Decoder pair.

The Encoded 12 bit output data obtained from HT12E has to be given here.

They are paired with 2 12 series of encoders. This pin powers the IC should use only 5V. This oscillator can be used by connecting these two pins through a 1M Resistor. So out of the bits 8-bits will be used to set address and the remaining 4-bit will be used to transmit data. A basic circuit diagram for the HT12D IC is shown below In the above circuit I have set the 8-bit address data as 0b, by connecting all address pins to ground.

  KTY82 220 PDF

For decoding a data the IC will requires an oscillatorluckily this IC has one in-built. If any valid data is received they can be obtained from these four pins. HT12D is a decoder integrated circuit that belongs to 2 12 series of decoders. It is mainly provided to interface RF and infrared circuits. Valid transmission; active high. Choosing Battery for Robots.

We should set the bits in same pattern on Encoder and Decoder IC to pair them. The input data code is decoded when no error or unmatched codes are found. In simple terms, HT12D converts the serial input into parallel outputs. Choosing Motor For Robots.

This oscillator can be used by connecting these two pins through a 1M Resistor 17 Valid Transmission VT This pin will go high when a data is received. So if you are working on a project which has to transmit a 4-bit data from one end to other either by wire or wireless then this IC pair will be best suited for you.

The serial input data is compared with the local addresses three times continuously. Supply voltage; 5V 2. The IC has a ht21d in oscillator. Interface SD Card with Arduino.

Arduino based GPS receiver. This pin will go high when a data is received. HT12D is capable of decoding 12 bits, of which 8 are address bits and 4 are data bits.