EN 12560-6 PDF
Find the most up-to-date version of DS/EN at Engineering BS EN Flanges and their joints. Gaskets for class-designated flanges. Covered serrated metal gaskets for use with steel flanges. DIN EN Flanges and their joints – Gaskets for class-designated flanges – Part 6: Covered serrated metal gaskets for use with steel.
|Published (Last):||2 May 2011|
|PDF File Size:||19.37 Mb|
|ePub File Size:||15.87 Mb|
|Price:||Free* [*Free Regsitration Required]|
Except as permitted under the Copyright, Designs and Patents Act no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means — electronic, photocopying, recording or otherwise — without prior written permission from BSI. Covered serrated metal gaskets for use with steel flanges – The price of the Standard included all amendments and correcturs.
Worldwide Standards We can source any standard from anywhere in the world. Non-metallic flat gaskets with or without inserts Part 2: A list of organizations represented on this committee can be obtained on request to its secretary. You may experience issues viewing this site in Internet Explorer 125606- 10 or Where the thickness of the location ring is sufficient a continuous colour 125660-6 the outer location ring shall identify the metallic sealing element core.
The general principles described in this standard shall also be applied to gaskets outside of the range specified 21560-6 Table 1 by agreement between supplier and customer.
For details of these and other benefits contact Membership Administration. 1260-6 sealing face shall also be free of surface blemishes, defects and damage that would impair the sealing performance of the gasket. Eh strips around the outer location ring shall identify the soft gasket covering layers. Where the thicknesses do not allow the clear marking of the edge of the ring or the core then the marking shall be on the upper and lower surfaces of the location ring.
The weight per unit area shall be such that metal to metal contact between the tips of the serrations and the flange surface is avoided. Sealing element with integral locating ring c Type LR: If using metric bolts in place 125606 imperial then the guidance notes on gasket assembly in B.
Flanges and their joints – Design rules for gasketed circular flange connections – Part 2: Flansche und ihre Verbindungen.
Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre.
EN b gasket type c nominal size — DN see Table 1 d class designation see Table 1 e required gasket materials or expected operating conditions for applications where ej gasket manufacturer is required to select gasket materials f type, thickness and density of facing material g type of metal for core and, where appropriate, for the locating ring.
For sizes below NPS 1. EN consists of 7 parts: However, with care, and dependent on the tolerances which have been used, it should be possible to fit the normal imperial dimensioned gasket when using metric bolting in existing imperial holes.
NOTE 2 Annex A lists information that should be supplied by 12506-6 purchaser when ordering gaskets in circumstances where the choice of the gasket materials appropriate to the service is left to the supplier. Learn more about the cookies we use and how 112560-6 change your settings. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Management Centre or to any CEN member.
BS EN 12560-6:2003
If these details are to be used for eh other purpose than implementation then the prior written permission of 12560-66 must be obtained. Copyright Copyright subsists in all BSI publications. Covered serrated metal gaskets for use with steel flanges Part 7: Joints pour les brides designees Class.
Spiral wound gaskets for use with steel flanges. Amendments issued since publication Amd. We would be grateful if anyone finding an inaccuracy or ambiguity while using 1260-6 British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover.
It is recommended that selection of gasket type of any particular application is in consultation 122560-6 the gasket supplier see annex A. Accept and continue Learn more about the cookies we use and how to change your settings. When installed the ring shall be sufficiently loose in the location slot in the core so that thermal expansion effects never cause the ring to become tight in the location slot.
Find Similar Items This product falls into the following categories. The pitch of the serration and the width of the serration shall be arranged so that the width of the tips is 0,1 mm.
Grooved Gaskets EN
The following information should be supplied by the purchaser when ordering gaskets: The serrations into metal core have the function of creating regions of high surface pressure on the conformable sealing material to ensure the required level of tightness in service.
Joints metalliques stries revetus pour utilisation avec des brides en acier. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Information on cookies usage.
Joints metalliques stries revetus pour utilisation avec des brides en acier Title in German Flansche und ihre Verbindungen. Brides et leurs assemblages. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service.