ELTAKO TLZ12-8E-230V UC PDF
Manufacturer name, Eltako. Manufacturer number, TLZEV+UC. GTIN, Country of origin, Germany. Customs tariff number, gThe Standardg TLZ12 8E 23 V UC replaces the TLZ12N0 V and TLZ12 8E V+V uC. gThe Allrounderg TLZ12D 23 V UC replaces the TLZ12M V+V uC. g The Simpleg . Also visit TLZ12D V +UC. Eltako Staircase time switch TLZplus 1; 2; 3; 4 Matching products. Eltako Staircase time switchTLZ Manufacturer, Eltako. Manufacturer.
|Published (Last):||20 September 2015|
|PDF File Size:||12.24 Mb|
|ePub File Size:||18.98 Mb|
|Price:||Free* [*Free Regsitration Required]|
Where more than one motor is controlled by an EGS12Z or in case the control voltage is different, one MTR12 must be connected to two motors.
The permanent power supply must be connected directly to a phase conductor ahead of the mains disconnection relay FR V. Sensor function and open circuit monitoring: This learn-in mode can be realised immediately after connection of the new load by briefly switching off the MCB. The settings ESL consider the special conditions regarding dimmable energy saving lamps: After installation and after a power failure the multisensor needs approx.
For mounting, use aluminium bracket, or the fastening screw that also comes with the device, directly on the KM1 plastic mounting bracket of the wind sensor.
These central control inputs A7 and A8 are used for the sensor relays MSR12 and LRW12D for the wind sensor, the frost sensor and the rain sensor functions as these are required to have absolute priority over other sensor commands. The brightness ylz12-8e-230v is stored on switch-off memory.
Afterwards the light is dimmed up in dimming time t max. Automatic reversal with 1s reversal time. The colour of the button is always the same as the LED, the rest is blue. The inrush current is 40mA. Due to this, the complete function remains but the leads to the lamps is disconnected by means of the switching-off relay. Signals from switches and momentary contact switches do not require series-connected sensor relays as they act directly on actuators. In the meantime central commands are not executed.
A telegram is transmitted within 20 seconds if the power status changes by min. Eltaok changeover buttons are blue. Wireless single-phase energy meter transmitter module, maximum current 16A.
A light sensor, for example, measures brightness and generates a control voltage as a function of it. At LSD set the brightness from 1 to 40 klux; this setting triggers the light-twilight signal as a 2-second impulse at output 3 in the event of an undershoot dependent on the set delay time.
Supply voltage same as control voltage. Here the capacitor tlz12-8d-230v in parallel to the mains is the deciding factor determining the correct dimensioning per lamp. G6Accessory base load A base load is used if loads cannot be detected due to their capacitance but are meant to switchon the line voltage.
Control power demand 0. We are there for you. When signals are detected again, each alarm stops automatically.
The simultaneous use of two potentials at the control inputs is not permitted. If N is connected, the zero passage switching is active. Eltqko product is no longer available. Dimmable energy saving lamps ESL up to watt. On all other functions, the set time, the function code and the contact symbol are shown in the correct position open or closed. A fold inrush current must be expected for electronic ballast devices. Control voltage V. The FRV mains etlako relay disconnects the power supply once all series connected loads are turned off, thus preventing any electromagnetic interference fields from occurring.
Tlz12 free download, or read Tlz12 online
The closing operation and the opening operation is also carried out externally at L of the SUD An LED behind the rotary switch indicates rain elta,o, at which point output 4 closes. The colour of the spherical cap is always the same as the LED.
Further capacity enhancers LUD12 in the mode “increase of capacity with additional lamps” can be connected to the controller SUD12 as described on page B5.
G7The Modular ApproachSwitching on the future. Function rotary switches Typical connections: Time-base figures available are 0. The ON tlz12-8w-230v is blue. The total time is obtained by multiplying the time base by the multiplier. The longest possible setting is 99 hours. Multifunction time relays always switch at zero dltako, the DX devices only when connected to N.
Holding down the push-button during the dimming down process dims up and stops the snooze function. To do this, program the changeover as follows: