DESIGNJET T1300 SERVICE MANUAL PDF

0 Comments

Print from a computer using the Embedded Web Server or HP Utility (T series). free Web service makes it easy to access and print large-format documents . It is possible to assign a manual IPv6 address to the printer, using the front. This Service Manual contains information necessary to test, calibrate, maintain and service the following: HP Designjet T 24inch; HP Designjet T 44inch;. HP DesignJet T and T Printer Series. Using your The only warranties for HP products and services are set .. Web Services manual configuration.

Author: Salrajas Tatilar
Country: Libya
Language: English (Spanish)
Genre: Video
Published (Last): 22 January 2011
Pages: 126
PDF File Size: 1.59 Mb
ePub File Size: 7.26 Mb
ISBN: 226-1-53210-322-7
Downloads: 44138
Price: Free* [*Free Regsitration Required]
Uploader: Shaktiktilar

Remove the four screws shown in the pictures. Remove the from the product.

If you try to install a Hard Disk Drive that was servuce used in a different product, the product displays a System Error and will not start manuxl. Remove all the printheads and insert them alone one by one, Closing the latch and the carriage cover after every insertion. The Touch Control Panel will then show the test results. Measure the total length of the two vertical rules at both sides of the copied plot we call it M1 and M2.

Network settings can be set manually, but in the majority of cases, they are obtained automatically from the product. In extreme circumstances, when a Printhead is inserted, it is possible that the product will not recognize it due to the build-up of ink on the electrical connection between the Printhead and the Carriage Assembly. Replace one component at a time and check whether the error has gone before replacing another component.

Assembly on page All. It gives you complete control of your printer: These settings include many different servvice, such as IP address and subnet mask, available gateways, host and domain names, etc. Remove another G1300 screw that secures the Starwheel Assembly to the product. The product performs two movements. Disconnect the Media Lever Position Sensor.

  DER FROSCHKNIG ODER DER EISERNE HEINRICH PDF

Remove the RFID support. Primer motor In the Diagnostics menu, scroll to Service Station and press on this menu option. Cable Power Engine to. Please enter a Product Number to complete the request.

Remove the center coupling.

If you see an error message, check that the sheet sensor is connected, and retry the calibration. Image Quality Maintenance Procedure Load the paper you wish to use. Remove the left T1030 hinge locking plate from the Top Cover. Once you continue the test, the Touch Control Panel displays the following messages: Reboot the Product Try to upgrade the firmware desigjnet, for more information, see Appendix B: Ink Setup failure Corrective action: Wait until you see the following message.

Click the file once to select it, then right-click and select Save target as.

This does not discard any changes made in the current screen. The best way to solve this problem is to report the error to HP servce.

HP Designjet T790 / T1300 / T2300 series. Service Manual

Use a flat-bladed screwdriver to unclip the left Print Zone Overdrive retaining clip and rotate the clip vertically. Asia Pacific and Oceania. The next procedure describes how to copy the Scanner IQ plot: Unplug both connectors shown in the picture. Grip the Encoder Strip and move it towards the left to take off the tension until you have completed the next step.

Removing designjett blue end first could damage the black end.

HP DesignJet T in Printer User Guides | HP® Customer Support

Ddsignjet you have an error code which is not documented in this Service Manual or you have an error which you cannot resolve, then report the error to the HP Response Center or the nearest HP Support Office. Remove the Right Roll Guide on page Remove the left panel. Insert the printhead slowly and vertically, straight down.

  I STAND HERE IRONING BY TILLIE OLSEN PDF

The Touch Control Panel prompts you to confirm that the dummy printheads are correctly dexignjet. Unclip the cables from the cable ties.

HP DESIGNJET T1300 ePrinter series Service Manual

This sensor should be calibrated whenever a new sensor is installed. Insert the new purgers, reconnect the power cord and desjgnjet on the product. There are two menu options to calibrate the Drop Detector: Slide the left Print Zone Overdrive to the left disengage the center coupling. Remove three T screws that secure the rear of the Right Scanner Cover. The new cable will arrive with a female end, which you will replace with the existing male end. The Touch Control Panel prompts you to load the paper.

Press on the Ink Menu icon and the following screen is displayed. Unscrew the pinch arm assembly. Remove the Roll Cover, Lower on page It must cover the line sensor so that the product detects it. Remove three T screws that secure the Left Scanner Cover.

DesignJet T T T Plotter Service Manual Download

This error can occur because the product has been dropped during transportation, causing structural damage. While securing the screw with a 10 mm wrench key, use an 8 mm wrench to tighten the nut. Page Manuual can choose from the following Preventive Maintenance Kits: