CD4066 DATASHEET PDF
The CDBM CDBC is a quad bilateral switch in- tended for the transmission or multiplexing of analog or digi- tal signals It is pin-for-pin compatible with. Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue any product or service without notice, and advise . CD Datasheet, CD Quad Bilateral Switch Datasheet, buy CD
|Published (Last):||1 April 2014|
|PDF File Size:||7.18 Mb|
|ePub File Size:||5.12 Mb|
|Price:||Free* [*Free Regsitration Required]|
Cd0466 to Build a Quad Bilateral Switch Circuit In this circuit, we will show how to connect a bilateral switch chip to inputs and outputs using the quad bilateral switch chip. This means that either side of the switch can be used as the input. Ddatasheet establishes sufficient power to the chip. To the inputs of the 2 switches, we feed an analog signal. Applying these principles, you can easily see how to use all 4 switches if wanted.
How to Build a Quad Bilateral Switch Circuit
The most common waveform is a sine wave. Each switch has a single input and a datashheet output terminal. One place it can be obtained is at Taydaelectronics at the following link: First, to power thewe connect 5V of power to V DDpin 14, and we connect the ground pin, pin 7, to ground.
When pressed down, the pushbutton makes the signal HIGH. A bilateral switch is so called because the switch can operate forward or reverse. In order for signals to pass through from the input side to the output side, the control or enable terminal must be HIGH.
With the control switch HIGH, then the switch closes and there can be an output.
So by a HIGH digital signal fed into the control terminal, we can pass an analog signal from the input terminal to the output terminal of the switch. When unpressed, the pushbutton has the signal LOW by default.
To the control terminals of the 2 switches, we connect a pull-down resistor pushbutton circuit. The pinout of the chip is shown below. V DD and ground, pins 14 and 7, are dataasheet power pins. In this circuit, we will show the basic functionality cdd4066 the chip by passing analog signals through 2 of the switches by digital control. The control terminal enables the input to go to output.
A bilateral switch acts as a single pole, single throw switch. The really functions as an analog switch. This enables the signal at the input to go to the output. Each switch has an input, output, and control terminal. The datasheet for the can be found at the following link: For this circuit, we are only going to be using 2 of the 4 switches.
What this cdd4066 is we feed an analog signal into the input of the switch and it reaches the output only if a HIGH digital signal is fed into the control or enable terminal.
How to Build a 4066 Quad Bilateral Switch Circuit
The is a pin chip. So current can flow in one direction and the other direction, depending on which side is the input. If a signal is fed into the input while datsaheet pushbutton is unpressed, no signal will appear at the output. If the pushbuttons are not pressed down, then no signal will appear at the outputs.
How the Circuit Works So, in order for this circuit to work, the pushbutton must be pressed down for each of the switches. As the quad term implies, the is composed up of 4 switches.
The is a quad bilateral switch circuit, meaning that is composed of 4 switches. It can be obtained cheaply at a number of online electronic retailers. So you will see vatasheet if you press down the pushbutton with an analog signal or digital signal at the datqsheet, that same signal will appear at hte output.
The has a wide operating voltage of 5VV. The quad bilateral switch chip is a chip that is made up of 4 switches. The is an IC composed of switches which are designed to switch analog signals via digital control. Each switch also has a control or enable terminal.
In this circuit, we will show how to connect a bilateral switch chip to inputs and outputs using the quad bilateral switch chip. The switches are labeled from 1 to 4. Without the control or enable switch, there can be no output. You can view the control terminal as the eatasheet which closes the switch so that the input signal can cross over to the output.