Our 33 Litre Front Loading Benchtop Autoclave, available in Classic and Autofill versions, is ideal for laboratory research and is low in water. Have a question about Autoclaves, Sterilizers or Steam Generators? Our FAQ page has the answers. All the machines are supplied with a user manual but sometimes it is not consulted! Astell offer training to operators, and this is a service I recommend to ensure.

Author: Gokus Kagaktilar
Country: Pacific Islands
Language: English (Spanish)
Genre: History
Published (Last): 23 September 2014
Pages: 75
PDF File Size: 5.30 Mb
ePub File Size: 7.76 Mb
ISBN: 776-7-28244-892-1
Downloads: 52455
Price: Free* [*Free Regsitration Required]
Uploader: Dajora

An optional Internal Thermal printer is mounted in the right-hand side of the control pod, to record the Sterilization Cycle progress. Consult Factory for details.

Our dedicated team of autoclave Service Engineers work nationwide to support our UK customer base. G StartDelay The Start Delay allows a delay time to be entered maual time the cycle is started, from hours. Note ; – List only present if the Printer option is fitted.

Smaller capacity autoclaves, including most circular section machines require servicing once or twice a year depending on regularity of use. If the cycle is started in error abort the program. Continued use of a machine which does not comply is a criminal offence under E. AMB – Ecofill 33 litres Model: If this display showsthe Float Switch sensor in the Water Tank has detected that the water level is too low, because the water supply to the tank is inadequate or has failed.

Freesteaming may not be required for simple loads where the steam can penetrate the load easily. If the printer mechanism works but no printing results – check that the paper has not been loaded upside down! The 33 to 63 litre front loading ‘Benchtop’ autoclaves zstell available in two versions.

The Astell 120 – 344 Litre Front Loading Autoclave Range

Don’t fill this field! It is intended to be used only by qualified engineers who have been shown how to perform such adjustments by the manufacturer’s agent, or who are carrying out such adjustments on behalf of or under the instruction of the manufacturer.


This may also be used to add clean water during a Chamber-cleaning operation. These should ideally be read by the operator and written down by the operator following the instructions on the display. Load the chamber and close the door.

Only parts supplied by the manufacturer as spares or accessories will ensure compliance with the directives. The Astell controller allows the programming of at least 50 different cycles. At the end there is a delay as the new values are stored in satell memory.

The collective knowledge gained here also helps us to support our ever-growing international customer portfolio handled through Astell’s central Service Department, which can offer on-site or off-site guidance to both UK and overseas customers.

A copy of the original Manufacturers Manual and literature is also provided. This will reset to the autoclwve settings for the program. Alternative sensors with Clips and Attachments, and a variety of Load Sensors are available for special load requirements.

Frequently Asked Questions | Astell UK

The media will be kept warm for up to 48 Hrs. During this period the Timing functions continue to run and the Temperature Control system will operate as normally but TIMES will not be visible to the operator until kanual Calibrate Mode has been left.

Please review our Privacy Policy for how we use your data. This will be accompanied by a autoc,ave audible beep tone. The slow reduction reduces boiling over of media. It must be set to an appropriate temperature that will operate safely for all programs and loads. Turns ON the RS communications option. Can the air ballast autoc,ave be used to speed up cooling?


An autoclave without an Autofill system will need to be manually filled before each cycle. Which options are required for pipette tips and textiles?

Selector Locking is set enabled in the Autoclaave Configuration section. These will wipe any settings previously entered by the user. Keep your machine regularly serviced and pay attention to the in-house maintenance advice we autoclafe with each new machine. See Page 42 MXN iss ed. The stages are as follows ; Note times, etc shown are illustrative and do not represent actual cycles. Please contact Astell for further details. If an autoclave has a steam generator little or no water remains in the end of the cycle.

The system cannot be started unless the closure is fully secured. Following the sterilization stage, a post vacuum removes the steam from the chamber. Astell benchtop ‘Ecofill’ units are one of the most energy efficient autoclaves available.

Kanual can then be independently heated by the steam supply to allow drying to take place at the end of a cycle, or can be flooded with water during cooling to aid cooling times.

To ensure long record life for the standard paper supplied it is best to take a clear Photocopy before archiving the printout. Note that this system is Active Only if program.

Benchtop autoclaves brochure KB. MXN Please consult your supplier if you require further copies to those provided with your Autoclave. Does a top loading, non-Autofill autoclave need to be filled before each use? It will not be possible to enter values below this figure. There are up to 8 Programs with a number of parameters which may be set.

Load Sensed Timing avoids this problem.