Honeywell Security Intrusion and Communications, ADEMCO, AlarmNet, IntelliSense, Apex, FBII, electronic security systems, burglary alarms and fire alarms for. Installation manual for the Honeywell wireless three-zone sensor. For help installing your , call The Honeywell is a wireless three zone sensor. Unlike other Honeywell wireless window and door sensors, the does not have an internal reed switch.

Author: Taur Milkis
Country: Qatar
Language: English (Spanish)
Genre: Business
Published (Last): 15 April 2013
Pages: 494
PDF File Size: 14.91 Mb
ePub File Size: 6.64 Mb
ISBN: 398-7-32160-284-6
Downloads: 64713
Price: Free* [*Free Regsitration Required]
Uploader: Zololkis

Mounting For proper orientation of the unit in relation to its wall mounting plate and the loop wiring, read all of this section before installing the unit.

If a contact loop is not to be used, no connection is needed across its terminals. Don’t show me this message again. Regular maintenance and inspection at least annually by the installer and frequent testing by.

A built-in cover tamper switch admco activated when the cover is removed. Each loop transmits a unique ID code to a wireless system receiver connected to the system control panel. Add to my manuals Add.

This warranty replaces any previous warranties and is the only warranty made by Seller on this product s. Disengage the supplied mounting plate from the unit by inserting the blade of a small screwdriver into the locking tab release window see Diagram 2 and pressing it against the case adenco tab see Diagram 1 while sliding the plate downward along the case back. Remove the ademvo cover if not already off as described in Mounting Step 1.

By pressing ‘print’ button you will print only current page. Although two holes are provided in the unit that would permit acemco directly to a surface holes “A” in Diagram 2it is recommended that the mounting plate be used, as described below, for ease in removing the unit for servicing should it become necessary.

Disengage the supplied mounting plate from the unit by inserting the blade of a small. If concealed wiring is to be used, feed the wires through the concealed wiring entry hole at. With the battery still not inserted, connect the loop wiring to the unit’s terminals see Diagram 2.


Customer understands that a properly installed and maintained alarm system may only reduce the risk of a burglary, robbery, fireor other events occurring without providing an alarm, but it is not insurance or a guarantee that such will not occur or that there will be no personal injury or property loss as 517 result. Replace battery only with: To replace the cover, engage the hooks along one edge and snap shut.

To print the manual completely, please, download it. The open slot at ademmco other end of the unit cannot be used as a cover pry-off. Except in the case of the position 4 ON setting, the Auxiliary loops are not affected 8517.

Recommendations must be included for a specific. Seller’s obligation shall be limited to repairing or replacing, at its option, free of charge for materials or labor, any product s which is proved not in compliance with Seller’s specifications or proves defective in materials or workmanship under normal use and service. For this application, the alignment guide strip along one edge of the plate serves no function and may be broken daemco, if desired.

The unit may, however, be installed in any direction, as long as the ademoc of the unit to its mounting plate qdemco maintained. Complain wrong Brand wrong Model non readable. Comments to this Manuals Your Name.

For UL installations, no contact in any of the loops may be more than 3 feet from the transmitter. For UL installations with fire zones, the position 4 ON setting must not be used. The locking tab will click as the case back locks in place. The description that follows assumes that the unit will be mounted as shown in the diagrams. Seller does not represent that the product s it sells may not be compromised or circumvented; that the product s will prevent any personal injury or property loss by burglary, robbery, fire or otherwise; or that the product s will in all cases provide adequate warning or protection.


Seller shall have no obligation under this Limited Warranty or otherwise if the product s is altered or improperly repaired or serviced by anyone other than Honeywell factory service.

Honeywell ADEMCO 3 Point Wireless Transmiter | eBay

Risk of fire, explosion, and burns. When a satisfactory location is found, remove the battery and proceed with installation. The installer should assume the responsibility of developing and offering a regular maintenance. It is not necessary to program the transmitter IDs during installation.

Do not recharge, disassemble, heat above. The should be treated as “RF” i. If concealed wiring is to be used, feed it through the slot in the case back but do not connect.

The has its own unique identification codes permanently assigned during manufacture. While the transmitter is being enrolled by the control, all DIP switch positions should. Surface wiring should enter via the thin “breakout” area provided in.

Attach the case back to the mounting plate by sliding the keyhole slots in the case back down. Dispose of used batteries promptly.

Honeywell ADEMCO 5817 Installation And Setup Manual: Wiring Connections; Specifications

Page of 2 Go. Enter zdemco from picture: The two Auxiliary Ademmco are closed-circuit, with a nominal response time of mSec. Got it, continue to print. The Multi-Point Universal Transmitter may have three contact loops connected to it. Don’t have an account? Observe correct polarity and insert the battery provided into the battery holder see. Install the mounting plate, with its case holding posts pointing up in this examplein the. The Primary Loop has several DIP switch selectable options that determine its connection requirements, response, and transmission characteristics see DIP switch setting table on next page.