ADC0808CCN DATASHEET PDF

0 Comments

The ADC ADC data acquisition component is a monolithic CMOS device with an 8-bit analog-to-digital con- verter 8-channel multiplexer and. ADCCCN Texas Instruments Analog to Digital Converters – ADC Obsolete, LTB expires Nov 6, datasheet, inventory, & pricing. ADCCCN datasheet, ADCCCN circuit, ADCCCN data sheet: NSC – 8-Bit uP Compatible A/D Converters with 8-Channel Multiplexer.

Author: Netilar Negrel
Country: Bermuda
Language: English (Spanish)
Genre: Video
Published (Last): 11 November 2016
Pages: 302
PDF File Size: 10.6 Mb
ePub File Size: 11.75 Mb
ISBN: 151-6-74139-657-6
Downloads: 15102
Price: Free* [*Free Regsitration Required]
Uploader: Mezitilar

Since the ADC IC can measure up to eight Analog voltage and also does not have an internal clock adc080c8cn requires more components to make it work compared to its predecessor ADC The obtained value is 2. When the conversion is complete the EOC pins goes low to indicate the end of conversion and data ready to be picked up. ADC is an 8 bit analog to digital converter with eight input analog channels, i. TL — Programmable Reference Voltage.

What is Web Browser. These three pins are used to select the channel.

ADC Technical Data

Skip to main content. Output digital pins which gives the result of the ADC conversion.

Connect to ground of the circuit. Datasheeg three bits have to be set as shown in the table below to access the respective analog channel. Interface SD Card with Arduino. The ADC needs some specific control signals for its operations like start conversion and bring data to output pins.

  ANTHONY DE MELLO WEZWANIE DO MILOSCI PDF

This is an input pin which is made high to start conversion. Choosing Motor For Robots. In the above circuit I have used a potentiometer to feed in a variable voltage of 0V to 5V to the IN1 pin and the present Voltage is read using a voltmeter. The input which is to be converted to digital form can be selected by using three address lines.

It is a pin Eight channel 8-bit ADC module. SPI Module of Arduino. Step size is the change in analog input to cause a unit change in the output of ADC.

Start adtasheet input pin; a low to high pulse is given. Interface GPS with Arduino. As you can see in the image the voltage value is 2. Has to be made high to get output on output pins.

Choosing Battery for Robots. Powers the IC typically with 5V.

IC ADC0808

Analog Channel 1 to 5. Input pin; a low to high pulse brings data to output pins from the internal datashert at end of conversion. Vref is connected to ground normally. This is an output pin which goes high once the conversion is over. This high-density System-in-Package SiP integrates controller, power switches, and support components.

  ABERRANT SALIENCE INVENTORY PDF

Has to be datasueet clock signals 0V-5V 20Mhz approx. The default step size is The step size is decided based on set reference value. Or even to use as a standalone ADC module. Clock input; to provide external clock. These 7 pins are the input pins for Analog voltage sensor. End of Conversion EOC.

Arduino based GPS receiver. Virgin Galactic — Commercial Space Flight.

End of conversion; output pin; goes low when the conversion is over. Submitted by admin on 13 October Output 2 -1 to 2 This pin is should be temporarily made high to select ADC channel.

ADC Pinout, How to Use & Datasheet

Hence, if you are looking for a ADC module with a decent resolution of 8-bit that could measure up to 8 channels then this IC is for you. Once the channel is set it should be enabled by making datashedt Address latch enabled ALE pin to go high momentarily. The right input analog voltage can be given to pins from IN1 to IN7, but the IC can read the voltage of only one channel at a time. That is adc0808cccn every increase of Digital output bit 4.