ASTM D3654 PDF
ASTM D – Designation: D /D M – 06 Standard Test Methods for Shear Adhesion of. ASTM D/DM: Standard Test Methods for Shear Adhesion of Pressure- Sensitive Tapes. A summary of ASTM standards relating to pressure sensitive tape is attached. The shear test procedures are also harmonized: ASTM D and PSTC.
|Published (Last):||12 February 2010|
|PDF File Size:||1.81 Mb|
|ePub File Size:||6.65 Mb|
|Price:||Free* [*Free Regsitration Required]|
Precision and Bias Test specimens should be taken from several rolls of a tape and, whenever possible, among several production runs of a tape. Conduct an analysis of the logarithm of the data to determine the desired descriptive or comparative statistics. Add to Alert PDF. Measure any slippage that has occurred to the nearest 1 mm [1?
The d33654 is mounted horizontally, tape side up, with the free end of the tape allowed to hang vertically over the rounded end.
France Stock lots. Take care in the choice of samples and when comparing results between? Panels showing stains, discolorations, or numerous scratches are not acceptable.
You can also visit our FAQ section and see our information section on the risks associated with counterfeiting.
ASTM D3654/D3654M – 06(2011)
It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Width of specimen for Procedures E, F, and G if other than 12 mm [0.
The tape must be at a true right angle to the bent The width of the bar for 75 mm [3 in. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters. ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard.
If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below. Procedure D measures the shear adhesion of a pressure-sensitive tape to a nonstandard fiberboard, liner board, corrugated board, or other surfaces which is agreed upon for testing.
Special isothermal box for scooters and motorcycles. This may or may not relate to the ability of the tape to adhere to other surfaces. ASTM D asrm tester is for the test of lasting adhesive of pressure sensitive adhesive tapes, labels and other interrelated products. Transport of foodstuffs or medical; warmth or cold Available in compartment simple, double or icebox typify Isothermal d365 icebox for two wheels, scooters, motorcycles typify NOTE 3—Take care that the?
The precision of tests conducted on nonstandard surfaces may be different than that described in Section Procedures B, C, and D may be used to determine the shear adhesion of the tapes generally used to close fiberboard boxes in packaging applications.
The use of an elevated temperature during test tends to reduce the duration of the test. The edges for about mm [5 in. These censored data may have a time to termination rather than a time to failure.
Allow the remaining mm [8 in. This gives the test results for the roll of tape under consideration in the sampling plan. The panel is mounted horizontally, tape side up, with the free end of the tape allowed to hang vertically over the round end of the panel. Proceed to Checkout Continue Shopping.
The lasting adhesive property could be obtained by measuring the displacement of specimen on vertical test plate or the time to failure at the load.
Good cohesion ast necessary for clean removal. The resulting means and con? The surfaces of similar fiberboards may exhibit considerable variation between mills, between batches from one mill, and within batches.
Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility.
Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend.
ASTM D shearing tester Cell Instruments Co Import Export
Link to Active This link will always route to the current Active version of the standard. Adtm can download and open this file to your own computer but DRM prevents opening this file sstm another computer, including a networked server. A specimen size of 24 by 24 mm [1 by 1 in. Wholesalers ads Partners Websites. The use of an elevated temperature during test tends to reduce the duration of the test. For Procedures F and G, substitute a?
Where width or other factors causing high adherence to backing make it impossible to remove the specimen at the prescribed rate, remove it at a rate as close to mm [30 in.
One company reports that, with care, the between laboratory standard deviation and the residual including within roll standard deviation may be higher or lower than reported here, depending on the tape type and manufacturer. The assessment may be within a roll of tape, between rolls or production lots.